COVID-19 Product Cleaning & Disinfection
Neurotronics Product Cleaning
Neurotronics Sensors
Instructions for Use, Rev. 19091801
To clean belt, wash by hand in warm water with a mild detergent, and air dry.
To clean sensor, wipe the plastic enclosure and wire set with either:
-
70% isopropyl alcohol
-
Bleach solution containing 0.6% Sodium Hypochlorite
Do not immerse the sensor in cleaning solution or allow liquid to get into any openings. Immersing the sensor will damage the device and void the product warranty. Ensure the belt and sensor are thoroughly dry before use.
Additional Cleaning Reference for Neurotronics Sensors
Sensors
-
TH01 Thermocouple Sensor w/ Hanger
-
TH01 Thermocouple Sensor
-
BP01 Body Position Sensor
-
PZ01 Piezo Limb Movement Sensor
-
RIP01 RIP Driver, Abdomen
-
RIP01 RIP Driver, Thorax
-
PZ01 Piezo Snore Sensor
Cleaning Options
-
70% Isopropyl Alcohol
-
PDI Super Sani-Cloth Wipes (EPA Registration Number: 9480-4)
-
PDI Sani-Cloth Bleach Wipes (EPA Registration Number: 9480-8)
RIP Belts and Heel Straps
-
Heel Straps
-
RIP01 RIP Belt, Large - 32"-78"
-
RIP01 RIP Belt, Medium - 21"-45"
-
RIP01 RIP Belt, Small - 15"-27"
Cleaning Options
-
Spray with Clorox Commercial Solutions Hydrogen Peroxide Cleaner Disinfectant (EPA Registration Number: 67619-24)
-
Wash by hand in warm water with a mild detergent, air dry
Nomad PMU800
Service Manual, Section 5.3, Page 50, Rev. 190411
Cleaning should be performed between patients and only be performed by the healthcare provider.
Inspect the Nomad for damage before cleaning.
The external enclosure surfaces of the Nomad system and accessories may be cleaned with a soft cloth and mild detergent.
To disinfect the outside surface of the unit, wipe it with a non-abrasive cloth with either an Ammonium Hydroxide, or Sodium Hypochlorite (maximum 8.25%) based consumer grade disinfectant. Use disinfectants according to manufacturer's instructions. After cleaning with disinfectant, wipe with damp soft cloth to remove chemical residues.
Allow the device to air dry or dry with a soft cloth.
Nomad connectors may be dusted with a clean cloth or compressed air but should not come into contact with any Liquid.
Inspect the Nomad for moisture or damage, and test operation after cleaning and before patient use.
Opening the enclosure of the device voids any warranties associated with the device.
Additional Cleaning Reference for Nomad PMU800
Nomad PMU800 Device
-
70% Isopropyl Alcohol
Nomad PMU800 Accessories
-
Nomad PMU800 Pouch and Strap
-
Nomad Carrying Case
Cleaning Options
-
-
Spray with Clorox Commercial Solutions Hydrogen Peroxide Cleaner Disinfectant (EPA Registration Number: 67619-24)
-
Wash by hand in warm water with a mild detergent, air dry
-
Sphinx PMU710
Service Manual, Section 3.1, Page 34, Rev. 180606
Cleaning should be performed between patients.
Inspect the Sphinx PMU710 for damage before cleaning.
The external enclosure surfaces of the Sphinx PMU710 system and accessories may be cleaned with a soft cloth and mild detergent.
To disinfect the outside surface of the unit, wipe it with a non-abrasive cloth with either an Ammonium Hydroxide, or Sodium Hypochlorite (maximum 8.25%) based consumer grade disinfectant. Use disinfectants according to manufacturer's instructions. After cleaning with disinfectant, wipe with damp soft cloth to remove chemical residues.
Allow the device to air dry or dry with a soft cloth.
Sphinx PMU710 connectors may be dusted with a clean cloth or compressed air but should not come into contact with any liquid.
Inspect the Sphinx PMU710 for moisture or damage, and test operation after cleaning and before patient use.
Additional Cleaning Reference for Sphinx PMU710
Sphinx PMU710 Headbox, Control Unit and Communications Cable
-
70% Isopropyl Alcohol
Sphinx PMU710 Accessories
-
Sphinx PMU710 Carrying Strap
Cleaning Options
-
-
Spray with Clorox Commercial Solutions Hydrogen Peroxide Cleaner Disinfectant (EPA Registration Number: 67619-24)
-
Wash by hand in warm water with a mild detergent, air dry
-
Sphinx PMU700
Operator’s Manual, Section 3.5, Page 12, Rev. 179025
The external enclosure surfaces of the SPHINX system and accessories may be cleaned with a soft cloth and mild detergent.
SPHINX connectors may be dusted with a clean cloth or compressed air but should not come into contact with any liquid.
Opening the enclosure of either device voids any warranties associated with the device.
It is the responsibility of Neurotronics to fix or replace any components or devices under warranty that become defective during normal operation under prescribed conditions.
Follow local governing ordinances and recycling instructions regarding disposal or recycling of the SPHINX or any components.
Additional Cleaning Reference for Sphinx PMU7010
Sphinx PMU700 Device and Cable
-
70% Isopropyl Alcohol
Sphinx PMU700 Accessories
-
Sphinx PMU700 Pouch and Strap
Cleaning Options
-
-
Spray with Clorox Commercial Solutions Hydrogen Peroxide Cleaner Disinfectant (EPA Registration Number: 67619-24)
-
Wash by hand in warm water with a mild detergent, air dry
-
USB DC Box
Polysmith User Manual 11.0, Section 19.4.2, Page 430, Rev. 2/21/2020
The external enclosure surfaces of the USB DC Box may be cleaned with a soft cloth and mild detergent.
Opening the enclosure voids any warranties associated with the device.
It is the responsibility of Neurotronics to fix or replace any components or devices under warranty that become defective during normal operation under prescribed conditions.
Follow local governing ordinances and recycling instructions regarding disposal or recycling.
Additional Cleaning Reference for USB DC Box
USB DC Box Device
-
70% Isopropyl Alcohol
Website Reference List